Email me and I can forward them to you. The Ford Explorer uses an in-line fuel filter to separate the debris from the fuel lines. Explorer Forum has probably saved you that much already, and will continue to save you money as you learn how to diagnose fix problems yourself and learn which modifications work without having to experiment on your own. But pry it out I did with a big screw driver. The new filter simply installs by pushing the fuel line fittings onto the filter until the fitting locks you'll hear it click. Take the safety clips off of the ends of the filter. When you need a fuel pump replacement for Ford Explorer, AutoZone provides the right products at the right prices, so you're sure to find the perfect match for your reliable ride.
Don't risk being unable to start your vehicle just because you have a faulty Ford Explorer fuel pump on the inside. Reinstall the lock clips over each fitting and the band clamp and filter bracket. If you drive a Ford Explorer than you already know that you have to sacrifice fuel economy for power. One way to get the best fuel mileage out of your Explorer is to regularly change the fuel filter. Remove the fuel filter 9155. May be one or more stuck-open injectors, or the coil pack is bad. Also, look under the passenger floorboard inside the frame rail.
Thanks for the help guys! Once disconnected the new filter is just snapped on the line with ease and the safety clips can be reinstalled and thus the filter remounted. Still grasping the fitting and tool together, pull them back in the direction for removal, keeping the tool inserted in the fitting important. Push the outlet line onto the filter until it locks in place. Then install the new filter, hose down any spilt gass on the frame or a rust you will get. Your problem may be one of the following: First check or just replace the fuel filter.
When looking to get a fuel filter for the Ford Explorer you can buy one from a number of different retailers. Next, the fuel pump may be worn out. Your support is greatly appreciated. Though its exact position on each vehicle may vary, the fuel filter is generally located between the fuel pump and fuel tank. Trace the fuel lines to a heat shield in front of the tank. To see just how plugged it was getting, try blowing backwards on the filter and you can see a lot of the sediment come out in the can.
Parts Geek is one of the leaders in offering fuel filters. Place the cover to the side. Try gently moving the fitting back and forth while it is still in place. Ford's Procedure Fuel Filter Removal and Installation 1. Usually they just stop working running.
Next, check the fuel pressure regulator. How will removing the gas cap remove pressure in the fuel lines? A special tool is required on most models to release the fuel line; however, it is relatively cheap and can be obtained at your local parts store. Usually located on the front fuel rail, drivers side. The filter is in front of the fuel tank and is covered by a heat shield and plastic cover. If so, unbolt it and remove it. They are available for the following Ford Explorer years: 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998, 1997, 1996, 1995, 1994, 1993, 1992, 1991, 11, 10, 09, 08, 07, 06, 05, 04, 03, 02, 01, 00, 99, 98, 97, 96, 95, 94, 93, 92, 91.
My trucks fuel filter is under the driver's side door and is held on by a clamp Godzilla would have problems prying the filter from. Slide the line off the filter. Allow the truck to idle for five minutes. That's what I mean, everyone says relieve the pressure but there doesn't seem to be a set way. Inspect around the fuel tank for any leaks.
Once you get a quality fuel filter you will have something to help ensure that your vehicle stays in the best shape possible. If this is so, what is the best way to get to it? The connector will lock once the line is pushed onto the filter far enough. Ensure the arrow on the filter is pointing toward the front of the vehicle. Contributed by Mark McLauchlin The real key to removing the special fittings from the fuel filter is the technique employed using the special fitting removal tool. Connect your new filter to the fuel lines using the quick release tool to clamp the lines to each end of the filter.
If you don't push the fitting all the way towards the filter first, the tool will not release the retainer spring and you won't be able to pull the fittings off. Usually located under the car in front of the rear axle, drivers side. Disconnect it and take the cap off your gas tank, then start your engine and let it run until it quits. Pull gently until the fitting is all the way back as far as it will move. You're just asking for fuel pump problems.