Never attempt to ride over large obstacles, such as large rocks or fallen trees. To install the panel 1. Always follow proper procedures when operating over obstacles as described in this manual. Cylinder head air bleed bolt the clamp screw. Check the hoses periodically and, if dust or water collects in them, empty them and clean the air filter element and air filter case.
The headlights and taillight come on when the light 1. If the indicator light does not carefully. To change the engine oil with or without oil fil- ter cartridge replacement 1. It must open smoothly and spring back to the idle position when released. With the purchase of this Yamaha, you can now appreciate the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields.
Unhook the headlight bulb holder, and then remove the defective bulb. Al- hills as described in this manual. Uneven adjustment can cause poor handling and loss of stability, which could lead to an ac- cident. Avoid crossing the side of a steep hill if possible. Rear storage compartment cover The rear storage compartment is located under the seat. Cover at the rear of the headlight 1.
Remove the quick fasteners, and then push inward on the areas shown. Always make sure the throttle lever free play is adjusted to 3. Panel F To install the panel Place the panel in the original position. You cannot back up many of my competitors manuals; You run the risk of losing the data and having to re-buy the manual. Tap the tailpipe lightly, and then use a wire into the muffler and align the bolt holes. The Service Manual for Yamaha Grizzly 700 contains: General Information Specifications Periodic Checks and adjustments Chassis Engine Cooling System Carburetors Fuel System Electrical System Fuel Injection System Drive Train Troubleshooting Buy now the Factory Service Manual Yamaha Grizzly 700 2008 for instant download. Carrier bolt under the fenders Panel I To remove the panel 1.
Carrier bolt under the fenders 1. I will work harder to satisfy you than any of my competitors on the internet. Install the oil level check bolt and oil filler bolt, and then tighten them to the specified torques. Disconnect the hose on the coolant reservoir side, and then drain the coolant from the cool- ant reservoir. All air must be bled from the brake system. Select the appropriate switch position according to the terrain and the conditions. Place the panel in the original position, and Tightening torque: then install the quick fastener screws.
If the fuse immediately blows again, have a 5. Adjust the headlight beam if necessary. Make sure to properly connect the battery er, have a Yamaha dealer charge your bat- leads to the battery terminals. Keep Your All-Terrain Vehicle Running Smoothly. If the light does 4. Remove the air filter case cover by unhooking from the air filter case. When riding with cargo or towing a trailer : Reduce speed and allow more room to stop.
Im- proper throttle operation could result. The manual has detailed illustrations and step by step instructions. To access the storage com- partment, remove the storage compartment cover. To access the storage com- partment, remove the storage compartment cover. Disconnect the hose on the coolant reservoir cooling system with clean tap water. Bolt To remove the panel 4. Tapered nuts are used for both the front and rear wheels.
If unex- pected and uncorrected, sliding could lead to an accident. Install the rear carrier by installing the bolts 2. Bolt To remove the panel 4. The long seat is to al- with engine size greater than 90 cc. Clean the mesh with solvent, and then wipe the solvent off. Panel H Panel I 2. Carrier bolt under the fenders 1.
Turn the brake pedal free play adjusting nut in. Clean the mesh with solvent, and then wipe from the air filter case. Remove the rear carrier by removing the bolts. After draining the coolant, thoroughly flush the 7. This service manual has detailed illustrations as well as step-by-step instructions.
Refer to this section each time a panel needs to be removed and installed. Dismount on the uphill side or to a side if pointed straight uphill. Headlight beam adjusting screw this adjustment. Periodic Checks and Adjustments 4. Operating without eye protection can result in an accident and in- creases your chances of a severe injury in the event of an accident.