Place the new bushing on the reaction stay. Refer to the Accesses section of chapter 2. Selection of the next item on a menu. Lower the rear axle as far as the shock absorbers will permit the rear wheels should be on the floor. The conventional leaf spring has a high internal friction due to the fact that the spring leaves lie together and develop friction when moving against each other during spring movements. Return to the optimum sill height Press the control up or down twice in succession, the opposite of the position of the load sill.
Grease the edges of the bellows with Wabco West 1 or corresponding. It is recommended that the same recording standard is always used for an individual disc, with as low a speed as possible for optimum sound quality. Service overdue With the engine running the spanner remains lit until the service has been carried out. Deactivation is confirmed by the diode which is lit. Air distribution Air distribution is directed by turning the control towards: the side vents and the central vents,.
Fit but do not tighten up the retaining bolts. Do not rely on just a visual check. This equipment only operates once. Remove stop sleeve and stop screws. Connect the control rod level valve and fill the compressed-air system.
Locking the vehicle with exterior protection only If, while you are away from the vehicle, you wish to leave a window partially open or a pet inside the vehicle, you should choose exterior protection only. The nitrogen gas within the suspension sphere is separated from the hydraulic oil through a rubber membrane. The gauge is positioned on: - 1: the fuel tank is full, approximately 80 litres. The time it takes will depend on the resistance provided by the damping piston. Check that the seat belt is fastened by pulling the strap. Since the system recirculates fluid continually through the reservoir, all the fluid was repeatedly exposed to the air and its moisture content. Lower: downwards adjustment of the platform sill Press the control downwards continuously.
These will not hinder inflation of the lateral could cause injury to the head when the Wear a correctly adjusted seat belt. This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system. Jack up under the rear axle, place stands under the frame members behind the crossmember, at a height of approximately 600 mm. Connect hose in bottle to outlet on bellows. The red diode, located on the centre console, flashes once per second.
The headlight is on the front part of the cavity and on the back part you will see a small batwing shaped device with a finned heatsink. Place a pressed-in sleeve made according to the drawing on on the spring eye. Testing a spring The springs can be tested in a hydraulic press. When the lighting reaches the minimum or maximum setting, release the button then press it again to increase or reduce the brightness. Make a note of any shims at the reaction stay's front attachment rear axle casing.
The oil is forced to pass from the one side of the damping piston to the other. Remove the red battery terminal +. When this occurs with the engine running it is due to the start of saturation of the particle emission filter exceptionally prolonged urban type driving conditions: low speed, long traffic jams,. The relay has 4 connections labelled A, B, C and D Could anyone provide a wiring diagram or instructions on how to test these??? They also have advantages related to handling and control efficiency, solving a number of problems inherent in steel springs that suspension designers have previously struggled to eliminate. The Jukebox function permits the selective playing of up to 10 hours of music.
Jack up the bus approx. Unsourced material may be challenged and removed. Lower the window fully, then raise it, it will rise in steps of a few centimetres each time the control is pressed. The only passage is between the damping piston and housing. Good practice The anti-lock braking system comes into operation automatically when there is a risk of wheel lock. Exceeding the programmed speed Pressing the accelerator pedal in order to exceed the programmed speed will have no effect unless you press the pedal firmly beyond the point of resistance. Unscrew the cap integrated with the gauge and check the is indicated by lighting of the Otherwise, you risk seriously damaging your.
Fit the U-bolts and connect up the anti-roll bars. To re-install, engage the head restraint rods in the holes, making sure they are aligned with the seat back. The suspension was attached to sub frames that were fitted to the body through flexible mountings, to improve even more the ride quality and to reduce road noise. This surface is so designed that it can provide a suitable rolling radius for the bellows from the viewpoint of lifetime. Water bleeding, Diesel filter Engine fuses 148, 151.
Page 131 132 Air bags Good practice Sit in a normal upright position. Testing and adjusting removed level valve Special tools: 2788 two , 2800 Use test bench 2800 for testing and adjusting the level valve. The seriousness of the collision depends on the nature of the obstacle and the speed of the vehicle at the moment of impact. Most hydraulic brake systems are sealed from the outside air by a rubber diaphragm in the reservoir filler cap, but the Citroën system had to be vented to allow the fluid level in the reservoir to rise and fall, thus it was not hermetically sealed. France was noted for the poor quality of its roads after , but the hydropneumatic suspension as fitted to the and later cars reportedly ensured a smooth and stable ride there.