Unpublished rights reserved under the copyright laws of the United States. Is the Print cartridge damaged or obstructed by debris? Reduce the amount of data being scanned for the Fax or add memory to accommodate larger Faxes. Instructions for repacking the printer are included in the kit. However, there is no guarantee that interference will not occur in a particular installation. Are the Guide Claws damaged? Pull the Fuser out from the printer. Caution Do not touch the surface of the Transfer Roller. The Front Cover is not latched.
Check the speaker connection on the Replace the Reseat the Fax Board. Error messages or codes listed on the Error Information Report page. Release the wiring harness from the retainers. No Go to step 2. Country codes should be set prior to connecting this product to the network. If necessary, contact a licensed electrician to install a properly grounded outlet.
You can select rates between 5% and 10%. Printer problems not directly indicated by, or associated with an error message are covered in Chapter 4, General Troubleshooting. Remove and inspect the Transfer Roller. Warning Hazardous voltage is connected to the Power Supply. Check the Print CartridgeCheck the amount of toner remaining. These are used to evaluate printer performance and operation.
Remove the Rear Cover page 8-61. The manual feeder holds 1 sheet. Test the printer to be sure you have corrected the initial problem and there are no additional problems present. Fuses Warning Do not install a fuse of a different type or rating. Lift and remove the Platen Assembly. Close when the cover is closed? Replace the Tray 2 Feed Roller 8-14. The Go To column references the page number for the procedure.
Density is uneven between left and right sides. Transfer Roller Is the Transfer Roller surface 8-10. Call the Fax from a different line to check response. Non-Xerox or Third Party Print Cartridges can cause malfunctions, print-quality problems, and jam errors. Users should make sure their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe systems, if present, are connected together. Do not remove a replacement component or electrical sub-assembly from its protective package until you are ready to install it. Fuser Temp displays the current Fuser temperature.
Refer to the customer documentation for this procedure. When data is received, the printer should exit power save mode. Wait at least 30 minutes for the printer to cool before moving or packing the printer. This manual assumes that the reader is a qualified service technician. Remove 2 screws 12 mm, silver that secure the duplex path frame.
No Connect or replace the line. Remove 2 screws 12 mm, silver that secure the duplex path frame. Warning Notice: No 111 or other calls can be made from this device during a main power failure. If you are using downloaded fonts, verify that the fonts are supported by the printer, the host computer, and software application. Printing n Lower than -20 C for more than 10 seconds. Typically, the Tx level should be under -12 dBm.
The following techniques will reduce the occurrence of component damage caused by static electricity. If requested, this number must be provided to the telephone company. Print a Configuration page and verify the firmware information. Values of 0 to 15 are available with the default being 6. The Power Save can be set from 1 to 120 minutes. Rear Guide Unit 032N00491 115.
When the error occurs, the engine stops all functions and keeps it at error state. Appendix A - Reference: This section provides an illustration of the printers Control Panel menu structure, printer firmware update instructions, and a list of acronyms and abbreviations. Cartridge and inside of the printer. Mounting surface flatness must be within the specified range. . Is the Print Cartridge damaged? Match the defect to one or more of the following examples.
Recovering from Heat ErrorHeat error is automatically recovered when the error is only caused by low heat error, and not the heat errors in Warm-Up state and the over heat error. Is there debris in the media path? Use Service Diagnostics to check the printer and optional components. Notches s3210mfp-016 Apply pressure on the lift plate while pressing the white tab to release the lift plate. Penalties of fine or imprisonment may be imposed on those guilty of making such reproduction. Left Side Right Side s3210mfp-224 Lift and remove the Upper Exit Frame. Reseat connections on the Main Replace the Complete.